The Nissan Path Forum Index The Nissan Path
The World Wide Nissan Pathfinder Owner's Forum
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Use Google to search TheNissanPath forums ->
Suspension REBUILD

 
Post new topic   Reply to topic    The Nissan Path Forum Index -> R51 Suspension and Steering
View previous topic :: View next topic  
Author Message
Code Pathfinder



Joined: 18 May 2017
Posts: 57
Location: Minnesota

PostPosted: Fri Mar 08, 2019 1:01 pm    Post subject: Suspension REBUILD Reply with quote

Now that spring break has started for me, I can begin with the suspension rebuild.

Almost all of it Rolling Eyes

Yesterday I installed brand new struts from MOOG Suspensions. These struts were paired with a 2 inch lift spacer from Supreme Suspensions that I was already running with the old struts.



Here it is installed







I haven't noticed any unusual darting to veering with the new struts. Wheels appear to be in the same position last time and the height in the front didnt change with the new struts. I will get an alignment soon just gotta schedule it.

I attempted to install the lower control arms in the front and rear today and im running into the same issue.

My lower pinch bolts in the front and rear and the upper pinch bolts in the rear that clamp the ball joint to the knuckle are seized pretty bad.

Im letting them sit in PB Blaster for a couple of days before I try again.

if that doesn't work then ill cut the ball joint off and remove the knuckle from the assembly to drill out the old pinch bolts.

the new pinch bolts from Nissan are fairly cheap. Last time I checked they were around $2.00. the nuts go for $0.98 each.
_________________
2009 Nissan Pathfinder S V6 4.0 Liter Engine
NISMO OFF ROAD CONCEPT BUILD
NISMO CAI, Radiator Cap, Oil Cap
Firestone Destination Le2 P245/75/R16
2 Inch Suspension lift
Supreme suspensions 1.5 inch wheeel spacers
Bilstein 4600 Series Shocks
Off road lighting
Bullbar
Black Trim Headlights
RGB Rock lights
12 inch Subwoofers
2500W Amplifier
Back to top
View user's profile Send private message
Thupertrooper



Joined: 15 Jun 2013
Posts: 555
Location: Mesa,AZ

PostPosted: Fri Mar 08, 2019 10:55 pm    Post subject: Reply with quote

I hope the PB blaster gives you a break but sounds like cutting is your easiest option.
_________________
2005 OR Pathy V6 Volant CAI
Lift-Long Travel front(5+ lift)
Drop bracket rear 4" plus Armada springs and spacers.
Airlift1000(uneeded now) Longer 5100s.
Lokka front locker.
35s On Vision Rims.
Custom Dual Swing out rear bumper
Kenwood2m HAM Midland CB Firestik FreeSpritRecreation Series Small Canopy Roof Top Tent(If in the market DM for deals) ---
Back to top
View user's profile Send private message
Code Pathfinder



Joined: 18 May 2017
Posts: 57
Location: Minnesota

PostPosted: Sat Mar 09, 2019 9:06 pm    Post subject: Day 2 Reply with quote

So PB blaster and a new control arm made my day!

The pinch bolt for the ball joint came out with some hammering and the ball joint was pressed out of the knuckle using a pitman arm puller ( this is a must have for this. you will thank me later Smile )

Here is the new control arm on the passenger side (im doing the drivers side tomorrow).






Here is the old control arm. It turns out I didn't have adjustable cams in the front before cutting them out.



Seized Bolt Nightmare (same story on both sides) Shocked



I set the camber as close to factory as I could using a method I saw in a titan swap video. The video maker explained where the cam washer needed to be when aligning the control arms. Gonna get it aligned on Monday when the front control arms are all done.

The rear control arms are getting put on hold for now. Gotta order new uppers for the rear before tackling that project.
_________________
2009 Nissan Pathfinder S V6 4.0 Liter Engine
NISMO OFF ROAD CONCEPT BUILD
NISMO CAI, Radiator Cap, Oil Cap
Firestone Destination Le2 P245/75/R16
2 Inch Suspension lift
Supreme suspensions 1.5 inch wheeel spacers
Bilstein 4600 Series Shocks
Off road lighting
Bullbar
Black Trim Headlights
RGB Rock lights
12 inch Subwoofers
2500W Amplifier
Back to top
View user's profile Send private message
Code Pathfinder



Joined: 18 May 2017
Posts: 57
Location: Minnesota

PostPosted: Sat Mar 09, 2019 9:10 pm    Post subject: Reply with quote

I also accidentally stripped one of my bolts that holds the sway bar to the frame.

how is that issue fixed? it appears the nut is welded on to the frame.
_________________
2009 Nissan Pathfinder S V6 4.0 Liter Engine
NISMO OFF ROAD CONCEPT BUILD
NISMO CAI, Radiator Cap, Oil Cap
Firestone Destination Le2 P245/75/R16
2 Inch Suspension lift
Supreme suspensions 1.5 inch wheeel spacers
Bilstein 4600 Series Shocks
Off road lighting
Bullbar
Black Trim Headlights
RGB Rock lights
12 inch Subwoofers
2500W Amplifier
Back to top
View user's profile Send private message
palmerwmd
Site Admin


Joined: 31 Jan 2017
Posts: 678
Location: Virginia

PostPosted: Sun Mar 10, 2019 12:13 am    Post subject: Reply with quote

Nice goodies!! Very Happy

You Sir are my hero ..
Cant help with the bolt but i am sure someone else will have some good tips
_________________
"Rifle first, Rifle last, Rifle always"

2012 V6 4WD, in Grey over Grey
Back to top
View user's profile Send private message
smj999smj
Site Admin


Joined: 22 Jan 2012
Posts: 5058
Location: Prospect, VA

PostPosted: Sun Mar 10, 2019 12:59 pm    Post subject: Reply with quote

Code Pathfinder wrote:
I also accidentally stripped one of my bolts that holds the sway bar to the frame.

how is that issue fixed? it appears the nut is welded on to the frame.


Can the nut be heated with a torch and taken off with vice grips or something similar?
_________________
2006 Pathfinder LE VQ40DE AWD, aftermarket radiator, Airlift 1000's, Bilstein HD rear shocks, Doug Thorley shortie headers and mid-pipes, Magnaflow 12580 muffler, aFe Momentum GT CAI w/ dry filter, XTP plenum spacer, Superchips Flashpaq tuner
Back to top
View user's profile Send private message Send e-mail
Code Pathfinder



Joined: 18 May 2017
Posts: 57
Location: Minnesota

PostPosted: Sun Mar 10, 2019 7:14 pm    Post subject: Day 3 Reply with quote

Front suspension is done.

New lower control arm installed on the drivers side with Moog camber bolts.

A FEW NOTES:

1. I cannot stress this enough, get a pitman arm puller. This thing made my job a lot easier getting the ball joint out of the knuckle.

2. the drivers side pinch bolt was still stuck even after soaking in Pb blaster last night. I cut off the ball joint (see photo down below) to separate the old LCA from the knuckle.

I then proceeded to use my pitman arm puller to press out the stuck bolt in the knuckle. I needed to hit the bolt with the impact to get it to spin before I did this. once it began to spin, I was in business.

3. Impact wrench and heat are your best friends. I personally didn't have a torch but my impact wrench saved my rear end from hours of frustration and difficulty dealing with stuck nuts and bolts.

4. Add anti seize to your new camber bolts and control arms bushings. This will prevent the bolt from getting stuck in the bushing again.

5. I was able to get my sway bar bolt to thread back into the nut. I cut off the damaged threads on the bolt and slowly threaded the bolt back in.

Off to get an alignment tomorrow and recycling my old car parts for some $$$ Laughing

Finished install pics







Aftermath of my old suspension





Here is the LCA where the joint was cut.


_________________
2009 Nissan Pathfinder S V6 4.0 Liter Engine
NISMO OFF ROAD CONCEPT BUILD
NISMO CAI, Radiator Cap, Oil Cap
Firestone Destination Le2 P245/75/R16
2 Inch Suspension lift
Supreme suspensions 1.5 inch wheeel spacers
Bilstein 4600 Series Shocks
Off road lighting
Bullbar
Black Trim Headlights
RGB Rock lights
12 inch Subwoofers
2500W Amplifier
Back to top
View user's profile Send private message
Code Pathfinder



Joined: 18 May 2017
Posts: 57
Location: Minnesota

PostPosted: Fri Mar 15, 2019 12:58 am    Post subject: Reply with quote

Forgot to post regarding the alignment results

The front end is now back to factory specs.

The rear is still off. No surprise there Rolling Eyes

I ordered new rear upper control arms for both sides so i can replace the lower control arms.

Almost every bolt that goes into both rear knuckles are seized on my pathfinder. Nothing my powerful impact and sawzall cant handle Laughing

I do post a question for anyone who can answer for me

How do you remove the parking brake cable from the rear knuckle on the R51 pathfinder?

I need to do this so i can use my pitman arm puller to press out the seized pinch bolts that are stuck in the knuckles.
_________________
2009 Nissan Pathfinder S V6 4.0 Liter Engine
NISMO OFF ROAD CONCEPT BUILD
NISMO CAI, Radiator Cap, Oil Cap
Firestone Destination Le2 P245/75/R16
2 Inch Suspension lift
Supreme suspensions 1.5 inch wheeel spacers
Bilstein 4600 Series Shocks
Off road lighting
Bullbar
Black Trim Headlights
RGB Rock lights
12 inch Subwoofers
2500W Amplifier
Back to top
View user's profile Send private message
BullDozer



Joined: 17 Jan 2016
Posts: 129
Location: Detroit, Michigan

PostPosted: Sat Mar 16, 2019 8:37 pm    Post subject: Reply with quote

Thank you for all the pictures

Regarding removing the e brake. There is a link in one of the stickie to nissan tech manual
_________________
2006 SE 4.0 4x4
Rancho quick strut front
Armada rear springs, Rancho rear shocks
265/75 R16 Cooper AT3
Back to top
View user's profile Send private message
palmerwmd
Site Admin


Joined: 31 Jan 2017
Posts: 678
Location: Virginia

PostPosted: Sat Mar 16, 2019 9:07 pm    Post subject: Reply with quote

O many nice pics! Surprised

Also It must feel good to look under the vehicle and see so many shiny new suspension components! Very Happy
_________________
"Rifle first, Rifle last, Rifle always"

2012 V6 4WD, in Grey over Grey
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    The Nissan Path Forum Index -> R51 Suspension and Steering All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group