How fast can you go in 4H?

The Gas and Diesel Engines - VQ40De, VK56DE, YD25DDTi, V9X, Transmission, Transfer Case, Oil, Differentials, Axles, Exhaust...

Moderator: volvite

User avatar
GimmieSumMo72
Posts: 142
Joined: Tue Oct 28, 2008 8:32 am
Location: Edison, NJ

How fast can you go in 4H?

Postby GimmieSumMo72 » Mon Dec 29, 2008 7:57 am

Not sure who left the Pathfinder in 4H (my bro or wife) but I came back from vacation late last night and rushed off to work this morning.

I didn't notice that the car was in 4H. I was flying down the Turnpike at like 85+ mph.

Just wanted to know how fast can you go in 4H and if I did any damage?


Thanks!

Mo.


User avatar
Pappy
Posts: 53
Joined: Sun Dec 21, 2008 8:28 pm
Location: Fort McMurray, Alberta

Postby Pappy » Mon Dec 29, 2008 8:27 am

Our test pilots have recorded 85+ so far. Anyone else top that?

NVRDONE
Posts: 159
Joined: Wed May 07, 2008 1:35 pm
Location: seattle

Postby NVRDONE » Mon Dec 29, 2008 8:39 am

I constantly run 75 + with no problems

User avatar
disallow
Site Admin
Posts: 2820
Joined: Wed Aug 13, 2008 9:02 am
Location: Winnipeg, Canada

Re: How fast can you go in 4H?

Postby disallow » Mon Dec 29, 2008 9:06 am

GimmieSumMo72 wrote:Not sure who left the Pathfinder in 4H (my bro or wife) but I came back from vacation late last night and rushed off to work this morning.

I didn't notice that the car was in 4H. I was flying down the Turnpike at like 85+ mph.

Just wanted to know how fast can you go in 4H and if I did any damage?


Thanks!

Mo.
I believe the key is not to shift in or out of 4H when moving faster than 50MPH (80KPH).

That being said, the best way to shift from 2H to 4H while creating the least wear on components is at a stop.

t

KEVSTER
Posts: 401
Joined: Sun Oct 12, 2008 8:21 pm

Postby KEVSTER » Mon Dec 29, 2008 6:50 pm

Uh you should only use 4H when the roads are ice or snow, in dry and rain you can use AUTO 4WD or just 2wd.

User avatar
GimmieSumMo72
Posts: 142
Joined: Tue Oct 28, 2008 8:32 am
Location: Edison, NJ

Postby GimmieSumMo72 » Tue Dec 30, 2008 10:38 am

KEVSTER wrote:Uh you should only use 4H when the roads are ice or snow, in dry and rain you can use AUTO 4WD or just 2wd.
uh... that goes without saying.

User avatar
GOTGOO
Sponsored Member
Posts: 387
Joined: Wed Dec 24, 2008 9:15 pm
Location: St.Louis, MO

Postby GOTGOO » Tue Dec 30, 2008 7:05 pm

You should be able to drive in 4H all the time since its an open front diff. At least thats what i am under the impression of so correct me if i'm wrong.

User avatar
disallow
Site Admin
Posts: 2820
Joined: Wed Aug 13, 2008 9:02 am
Location: Winnipeg, Canada

Postby disallow » Tue Dec 30, 2008 9:02 pm

GOTGOO wrote:You should be able to drive in 4H all the time since its an open front diff. At least thats what i am under the impression of so correct me if i'm wrong.
The owners manual states:

Page 5-17

CAUTION
Do not drive the vehicle in the 4H or 4LO
position on dry hard surface roads. Driving
on dry, hard surfaces in 4H or 4LO
may cause unnecessary noise, tire wear
and increased fuel consumption.


Also on Page 5-20

The 4H position provides greater traction.
Avoid excessive speed, as it will
cause increased fuel consumption and
higher oil temperatures, and could
damage drivetrain components.
Speeds over 62.5 MPH (100 km/h) in 4H
is not recommended.


That should end that debate... :)

t

User avatar
Pappy
Posts: 53
Joined: Sun Dec 21, 2008 8:28 pm
Location: Fort McMurray, Alberta

Postby Pappy » Tue Dec 30, 2008 10:19 pm

Terry, you are just one big bag of bad news. Now everyone will be walking the floor all night worried about that time they were cruzing along at 64.7 km and hit that patch of hard dry pavment!

You already have me wearing a stethoscope when I go out to start my truck!!!! LOL
Last edited by Pappy on Wed Dec 31, 2008 9:18 am, edited 1 time in total.

User avatar
dmasini
Posts: 54
Joined: Mon Jun 16, 2008 1:07 pm

Postby dmasini » Wed Dec 31, 2008 8:18 am

Man, 62.5?? You think they could have just rounded that up or down? :wink:

User avatar
disallow
Site Admin
Posts: 2820
Joined: Wed Aug 13, 2008 9:02 am
Location: Winnipeg, Canada

Postby disallow » Wed Dec 31, 2008 8:22 am

dmasini wrote:Man, 62.5?? You think they could have just rounded that up or down? :wink:
62.5 mph = 100 kph (native UOM in Japan)
Last edited by disallow on Wed Dec 31, 2008 8:33 am, edited 1 time in total.

User avatar
dmasini
Posts: 54
Joined: Mon Jun 16, 2008 1:07 pm

Postby dmasini » Wed Dec 31, 2008 8:28 am

Ah, there I go showing my ignorance again! haha

User avatar
disallow
Site Admin
Posts: 2820
Joined: Wed Aug 13, 2008 9:02 am
Location: Winnipeg, Canada

Postby disallow » Wed Dec 31, 2008 8:35 am

dmasini wrote:Ah, there I go showing my ignorance again! haha
Actually they did round up.

100KPH / 1.609 = 62.15 MPH

:)
t

User avatar
disallow
Site Admin
Posts: 2820
Joined: Wed Aug 13, 2008 9:02 am
Location: Winnipeg, Canada

Postby disallow » Wed Dec 31, 2008 8:37 am

Pappy wrote:Terry, you are just one big bag of bad news. Now everyone will be walking the floor all night worried about that time they were cruzing along at 64.7 MPH and hit that patch of hard dry pavment!

You already have me wearing a stethoscope when I go out to start my truck!!!! LOL
Well it seems as though I have the oldest R51 on the forum with the highest mileage, so I get to experience all of the issues first! :)

Seems my lot in life, this truck is a replacement for my 98 civic, which was written off in April. It had almost 300k kms on it when she bought it. It was a reliable car, but had its quirks too.

That and I am a pretty meticullous DYIer. My Father-in-law calls me a perfectionist. Hardly, he's the one with all the duct tape fixes on his 96 Caravan....

Just call me the wet blanket of the forum.... :)

t

User avatar
Pappy
Posts: 53
Joined: Sun Dec 21, 2008 8:28 pm
Location: Fort McMurray, Alberta

Postby Pappy » Wed Dec 31, 2008 9:20 am

Forum Wet Blanket....Let's make it FWB just to confuse the ranks!!!


Return to “R51 Engine, Driveline and Powertrain”