Navigation/DVD Bypass switch for 2006 Pathfinder

Oh yeah, it's the geek bling with flashing lights, just can't get enough.

Moderator: volvite

scboyd99
Posts: 7
Joined: Wed Sep 23, 2009 12:46 pm

Navigation/DVD Bypass switch for 2006 Pathfinder

Postby scboyd99 » Wed Oct 14, 2009 8:08 pm

Let me first start by saying thank you to kmjsuperfly for the original post for a 08 pathfinder navigation bypass switch. I wanted to post this for people with an 06 Pathfinder with navigation. This was much easier than I thought and only took about 1 hours. For the 06 there is only one wire to cut and it is under the passenger seat. If I miss any steps make sure you read kmjsuperfly's posting for a much more detailed post and pictures here:
http://www.thenissanpath.com/viewtopic.php?t=1809
#1 Remove the cup holder trim, center storage bin (no screws)
#2 Remove the center console (no screws)
#3 I used the blank spot in the center console for the switch
#4 The switch I used is SPDT

Image

#5 Install switch and run wires to the back part of the passenger seat.
#6 Here is a picture of the installed switch

Image

For the next step I pulled up the front seat to get access to the Nav DVD player
#7 Here is a picture of the back of the NAV DVD player from the rear seat

Image

#8 You want the connector on the right side (the smaller of the two) it is labeled B152 in the service manual. It is the 4th pin in from the left if you are looking at the end of the connector. It is pin # 66 and on my car it was a grey wire with silver dashes. The wire is called the Vehicle speed signal wire.

Image

#9 Just cut the wire and connect each end of the wire to the leads from the switch.

Image

Hope people with an 06 Pathfinder with Navigation find this helpful.


kev1n
Posts: 181
Joined: Sun Jan 04, 2009 5:04 pm

Postby kev1n » Fri Oct 30, 2009 8:02 pm

This is awesome! I did a similar thing on my i35 , and was hoping for something like this on the pathfinder. Thanks!

kev1n
Posts: 181
Joined: Sun Jan 04, 2009 5:04 pm

Postby kev1n » Fri Nov 13, 2009 10:55 pm

just finished this mod, I wanted to clarify something. that wire you have to cut in the harness is the 4th pin from the right if you are looking at the back of the connector, and the 4th pin from the left if you are looking at the female end of the connector. I almost got confused, but I got it right and mine was also gray with silver dashes.

Dougster
Posts: 7
Joined: Sun Apr 18, 2010 2:22 pm
Location: Orange County

Navigation Modification

Postby Dougster » Sun Apr 18, 2010 2:34 pm

Does anyone know if the modification described would work on a 2010 model? The interior looks pretty much the same...

Triprock
Posts: 10
Joined: Sat May 22, 2010 6:19 am
Location: NYC

Postby Triprock » Sun May 23, 2010 12:46 pm

Why run the wires to a switch? Why not just cut the wire and leave it cut?

Dougster
Posts: 7
Joined: Sun Apr 18, 2010 2:22 pm
Location: Orange County

Postby Dougster » Sun May 23, 2010 3:00 pm

Triprock wrote:Why run the wires to a switch? Why not just cut the wire and leave it cut?
I asked the same question and the author provided the answer--the wire is necessary to send speed information to the GPS. If you cut it (and leave it off) your GPS will eventually lose track of your location.

Kidd_Funkadelic
Posts: 23
Joined: Wed Jun 16, 2010 6:55 am

Postby Kidd_Funkadelic » Wed Jul 28, 2010 9:57 am

Does anyone know the exact model number on the switch? I'm having a hard time finding one that's an exact size match so it looks like it's meant to be there on the dash....

Thanks.

User avatar
mar1
Sponsored Member
Posts: 1043
Joined: Fri Jun 19, 2009 9:08 am
Location: Ca

Postby mar1 » Wed Jul 28, 2010 1:52 pm

honeywell MRS93‑11BB

Kidd_Funkadelic
Posts: 23
Joined: Wed Jun 16, 2010 6:55 am

Postby Kidd_Funkadelic » Thu Jul 29, 2010 10:06 am

mar1 wrote:honeywell MRS93‑11BB
Thanks this has me pretty close. But now that I know where I'm looking, can some one clarify something for me?

Looking at the spec sheet:
http://content.honeywell.com/sensing/pr ... 2_2_en.pdf

Wouldn't I want MRS93-12BB?

I interpret this:

11BB = On-Off-On
12BB = Off-None-On

To mean that 11BB had 3 positions, while 12BB has 2 positions? Or am I misunderstanding something?

Thanks for any insight!


Return to “NAV/GPS/Audio/Electronics”