Ok so I've installed it, took the Neg. wire off the battery for 15 mins. Put the Neg. wire back on the batt. and it started after 9 attempts. I left it run for about 15 mins. but did not drive it. Turned it off.
Later, it would not start. But, if I unplug the mas airflow sensor wires from the airflow's aluminum tube. Once unplugged, she started right up.
???
So, I now have had the Neg. wire off the battery for about an hour but it still wouldn't start unless I unplugged that mas sensor.
I unplugged that mas sensor, started the car, plugged the mas sensor back in, then drove it around the block. I think I need to drive it longer...?
Here are my pics
Remove all this stuff
https://www.dropbox.com/s/xe1irg59hh81j7x/01.jpg?dl=0
https://www.dropbox.com/s/c62y5cleis4z6x6/02.jpg?dl=0
https://www.dropbox.com/s/59gbnpw4tda3zmg/03.jpg?dl=0
Install this stuff
https://www.dropbox.com/s/9316n57vyxe35o6/04.jpg?dl=0
The circles below are,(from left to right) factory hose to be replaced by new one included in cai kit, another oem hose that will not be connected to anything?, and the mas airflow sensor to be plugged into new air pipe.
https://www.dropbox.com/s/wwwm9mtqh8vlssb/05.jpg?dl=0
Install 1st pipe onto throttle body.
https://www.dropbox.com/s/bue1vjz42cxi9ub/06.jpg?dl=0
Tighten hose clamp
https://www.dropbox.com/s/kcqv5j6gkas0ay8/07.jpg?dl=0
Install next hose clamp onto 1st pipe....
https://www.dropbox.com/s/1l89cjx9ra8twj5/08.jpg?dl=0
Install 2nd pipe onto 1st pipe...
https://www.dropbox.com/s/73j37m2x6j0wooq/09.jpg?dl=0
Slide hose clamp onto desired area and tighten
https://www.dropbox.com/s/f75gsjhtao2yjk7/10.jpg?dl=0
This hose came with the kit and will replace factory one leading to the Plenum. Install hose clamp at the right angle beforehand...
https://www.dropbox.com/s/75gsxe9jx2todzd/11.jpg?dl=0
Install hose now
https://www.dropbox.com/s/vwvin1t38dvyjg2/12.jpg?dl=0
Slide hose clamp down into place
https://www.dropbox.com/s/i0fixd84rk36et6/13.jpg?dl=0
Place hose clamp on other end of hose, place hose on cai pipe and slide clamp down into place
https://www.dropbox.com/s/y56x3a4ns9hfrna/14.jpg?dl=0
This cai kit came with new mas airflow sensor screws which were already in their spot. Remove them with a magnetized head so as not to lose them!
https://www.dropbox.com/s/vzr6zqj9m6e0y05/15.jpg?dl=0
Here's that other hose that I have no idea what to do with... anyone?
https://www.dropbox.com/s/q6l47r7tkjg9syy/16.jpg?dl=0
Although using the 'brackets' that came with this kit was possible, I'm not a huge fan of the way this looks...
I used the factory bolt here:
https://www.dropbox.com/s/bnbcos94zy46e6d/17.jpg?dl=0
This kit came with two straight pieces and two L-shaped bars. I placed my L-shaped bracket between the aluminum airflow pipe and the rubber seal of the filter. The hose clame tightens this up nicely. I decided later to place this L-bracket between the rubber seal and the hose clamp.
https://www.dropbox.com/s/5qlmsuciikzhhbr/18.jpg?dl=0
https://www.dropbox.com/s/tpcksa56ogfppcb/19.jpg?dl=0
I used the 2 bolts that came with this kit at #'s 1 and 3 but found another bolt in my bin to use in the center #2 shown below
https://www.dropbox.com/s/si7tclup25gcuo4/20.jpg?dl=0
Replace the mas airflow sensor careful not to loose the screws. Again, I don't really like this bracker thingy but it'll work for now.
https://www.dropbox.com/s/r5p7mvmvurvqy7i/22.jpg?dl=0