The Nissan Path Forum Index The Nissan Path
The World Wide Nissan Pathfinder Owner's Forum
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Use Google to search TheNissanPath forums ->
The best reason to install an XTP plenum spacer: spark plugs

 
Post new topic   Reply to topic    The Nissan Path Forum Index -> R51 Engine, Driveline and Powertrain
View previous topic :: View next topic  
Author Message
smj999smj
Site Admin


Joined: 22 Jan 2012
Posts: 5584
Location: Prospect, VA

PostPosted: Sun Feb 23, 2020 4:08 am    Post subject: The best reason to install an XTP plenum spacer: spark plugs Reply with quote

A number of VQ40DE owners have installed the XTP plenum spacer for performance gains, but there is another huge benefit to this mod. Those that have tried have found that replacing spark plugs on the stock VQ40DE can be a bit of a challenge. With a little patience and a good assortment of universals and extensions, it can be done; it takes me about 45-minutes to do a set of plugs now having done it a couple of times. Since the last time I did it on my 06 Pathy, I have installed the XTP spacer and what a difference it makes when it comes to replacing the #1 and #3 coil packs and spark plugs! Even with my fat hands and chubby fingers, I can now reach under the upper plenum and get to the coil bolts and can get the #1 coil pack out without having to disassemble it! It still takes some creative extension and universal assembly, but not nearly as much as trying to do it without the plenum spacer. So, here are some picks of this project:

There are a number of choices for spark plugs. 2005-2006 used NGK Laser Platinum 6240. In 2007-2012, Nissan switched to the NGK Laser Iridium 93759. Both of these plugs are 105,000 mile interval plugs (the Laser Iridiums will actually last 120,000 miles, easily). Either will work in any year of the VQ40DE without any change in performance nor gas mileage. The Laser Platinums are less expensive. Some opt for the NGK Iridium IX 4469, which will also work just fine and cost even less than the Laser Platinums, but they are also only rated for around 60,000 miles. They are also a single tip, Iridium plug compared to the double-tipped Laser Iridium and Laser Platinum plugs. About two years ago, Nissan introduced their Ruthenium HX plugs. They are their "latest and greatest" plug, being marketed by NGK as "the highest performance and life expectancy of any aftermarket spark plug line." They are priced just shy of the cost of the Laser Platinum plugs (about $8/each at Rockauto). For the VQ40DE, the NGK Ruthenium HX part number is 96355. I also replaced two coil packs; I got genuine Hitachi (made in Japan) coils for $35 from Rockauto. Hitachi makes some of the OE coil packs for Nissan, along with Hanshin and Denso.








I use my Milwaukee 3/8" cordless ratchet for jobs like this! It's great for loosening bolts and spark plugs and running the plugs down once I finger-start them, however, I use my Snap-On 3/8" torque wrench to put the final tightening on the plugs at 18-20 lb-ft. If using new NGK plugs, do NOT use a lubricant on them, like anti-seize, as Nissan instructs not to. The plug is plated and lubing the threads could affect the torque on them. I use a 10MM 1/4" drive universal socket and extension to get the coil bolts out.





Yes! I can get my fat hands in there! Thanks, XTP plenum spacer!





If you disconnect the harness clip from the bracket, you can move the harness out of the way on the right bank and get to #5 coil a little easier.




Getting the harness connector off of the #1 coil pack can be a bit painstaking, but doable:



In this case, it's spark plug socket, short extension with electrical tape to lock them together, universal, long locking extension. When installing, if it comes apart, long, needle noise pliers can pull out the extension and socket.







The #1 coil pack can even fit through the opening in the upper plenum with a little maneuvering now with the XTP plenum spacer:



The left bank is easy to access. The #6 coil/plug in the back requires a little bit of thinking to get through the between the coolant and A/C line.



Yes, some Nissan techs actually do use torque wrenches!


_________________
2006 Pathfinder LE VQ40DE AWD, aftermarket radiator, Airlift 1000's, Bilstein HD rear shocks, Doug Thorley shortie headers and mid-pipes, Magnaflow 12580 muffler, aFe Momentum GT CAI w/ dry filter, XTP plenum spacer, Superchips Flashpaq tuner
Back to top
View user's profile Send private message Send e-mail
Thupertrooper



Joined: 15 Jun 2013
Posts: 623
Location: Mesa,AZ

PostPosted: Mon Feb 24, 2020 6:53 pm    Post subject: Reply with quote

I actually tried to just go around the plenum last time with the XTP spacer but after I took off I realized it took alot longer to do that.

I also recommend just using alot of multi angle sockets.
_________________
2005 OR Pathy V6 Volant CAI
Lift-Long Travel front(5+ lift)
Drop bracket rear 4" plus Armada springs and Rancho spacers.
Airlift1000 5125s
Lokka front locker.
315/75/16 BFG KM2s On Vision Rims.
Custom Dual Swing out rear bumper
Kenwood2m HAM Midland CB Firestik ---
Back to top
View user's profile Send private message
smj999smj
Site Admin


Joined: 22 Jan 2012
Posts: 5584
Location: Prospect, VA

PostPosted: Mon Feb 24, 2020 9:49 pm    Post subject: Reply with quote

Thupertrooper wrote:
I actually tried to just go around the plenum last time with the XTP spacer but after I took off I realized it took alot longer to do that.

I also recommend just using alot of multi angle sockets.


It took me about 30 minutes with the plenum on and the spacer. That's with have the tools and parts already at the car and the hood open. It takes me about an hour and a half if I have to pull the plenum. About 40-45 minutes leaving the plenum on an without the spacer installed.
_________________
2006 Pathfinder LE VQ40DE AWD, aftermarket radiator, Airlift 1000's, Bilstein HD rear shocks, Doug Thorley shortie headers and mid-pipes, Magnaflow 12580 muffler, aFe Momentum GT CAI w/ dry filter, XTP plenum spacer, Superchips Flashpaq tuner
Back to top
View user's profile Send private message Send e-mail
underworld1001



Joined: 27 Nov 2016
Posts: 307
Location: Austin, TX

PostPosted: Thu Feb 27, 2020 6:23 am    Post subject: Reply with quote

My takeaway from this article is that I should invest in a Milwaukee ratchet. Very Happy
_________________
2011 SV V6 - BF Goodrich KO2 LT265/75 17-C, StopTech slotted rotors (934.42044), free air box mod, Xtreme Truck Performance IMS (http://extremetruckperformance.com/?page_id=6), Bilstein 4600's (F-24-197427 / R-24-197434), Moog springs (F-81280 / R-81119 ), CSF aluminum radiator (7029)
Back to top
View user's profile Send private message
smj999smj
Site Admin


Joined: 22 Jan 2012
Posts: 5584
Location: Prospect, VA

PostPosted: Fri Feb 28, 2020 3:12 am    Post subject: Reply with quote

underworld1001 wrote:
My takeaway from this article is that I should invest in a Milwaukee ratchet. Very Happy


Northern Tools has a special every now and then. For $199, you get the ratchet, charger, a 3-LED flashlight and two M12 batteries with a carry case. The ratchet puts out about 35 lb-ft; it's not going to blow lug nuts off of wheels, but it great for most under the hood jobs within reason. They recently released a new model that's 55 lb-ft:

https://www.homedepot.com/p/Milwaukee-M12-FUEL-12-Volt-Lithium-Ion-Brushless-Cordless-3-8-in-Ratchet-Tool-Only-2557-20/302451803
_________________
2006 Pathfinder LE VQ40DE AWD, aftermarket radiator, Airlift 1000's, Bilstein HD rear shocks, Doug Thorley shortie headers and mid-pipes, Magnaflow 12580 muffler, aFe Momentum GT CAI w/ dry filter, XTP plenum spacer, Superchips Flashpaq tuner
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    The Nissan Path Forum Index -> R51 Engine, Driveline and Powertrain All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group